Home > Turns On > Blue Monitor Port Not Working Correctly

Blue Monitor Port Not Working Correctly

Contents

Contents Satisfaction Survey Q1. Greetings from Sri Lanka. :D View all 8 comments Report Ram- Feb 9, 2010 at 07:31 PM When I start the computer I can get image on the monitor only if If you're having image corruption in digital mode then you may be able to solve it by lowering the screen refresh rate. If there is still no image, continue to the next section. check over here

If it gets bad enough then the monitor doesn't receive the clock signal at all and the EDID read fails. Yes No Q2. The corruption can happen for any number of reasons including: a weak DVI transmitter in the video card, a cable which is too long for the DVI data rate, a very I have no idea what this means. check it out

Computer Monitor Problems And Solutions

Solutions: install a monitor .INF file All modern monitors can provide EDID data to the video card which describes the capabilities of the monitor. Report puntojay- May 7, 2011 at 07:16 AM i have the same problem my monitor its a tv, free view and monitor all in 1. Do so at your own risk. 2. DVI troubleshooting: solutions Solutions: update your display drivers The "update your display drivers" dance is popular for a reason: it often works.

How do I get the image when I open in 'Normal mode'? I know the desktop is extended because the mouse stays of the edge as if there's room there and a quick screenshot shows what I should be seeing: A two monitor Figure : VGA connector cover Video card with 1 VGA port and 1 DVI port Covered VGA port - should not be used Check cable connections If you see the initial My Computer Turns On But Nothing On Screen You can troubleshoot those by swapping in known-good parts.

In case an item was changed in the BIOS, such as the primary display device setting, use one of the following sections to reset the BIOS back to its default configuration: Having the monitor off may affect whether the monitor returns the analog or digital version of the EDID data for monitors which have a DVI-I input. Thinking it was the video card, I called tech support and they sent me a new one... Get More Info Most video cards have two outputs but most people only use one of them.

The EDID data is sent over the DDC bus. Computer Turns On But No Display On Monitor Or Keyboard Check the power light indicator. Analog mode has more benefits than just being almost guaranteed to work. Method 4 - BIOS and Recovery Options If you can see the initial boot screen when you turn on your computer, but it goes blank once Windows starts to load, then

Computer Turns On But No Display On Monitor

And there is no input option or anything vaguely resembling it. http://www.samsung.com/hk_en/support/skp/faq/1039299 Figure : DisplayPort connector Figure : DisplayPort receiving connector Figure : DVI connector Figure : Examples of DVI receiving connector Common connections used currently are DisplayPort and DVI. Computer Monitor Problems And Solutions Well guess what? No Display On Monitor But Cpu Running The right part is showing DVI corruption.

Telling your monitor to work as digital only and then using a DVI-A or VGA cable is a sure way to a blank screen. http://windowsrefund.org/turns-on/computer-won-t-display-on-monitor.php It can be solved by adding a lower valued resistor in parallel with the improperly-selected pullup resistor. I checked and swapped cables and BIOS settings without success. Please Tell my why I am dissatisfied with the performance or quality of my product I am dissatisfied because my product requires service I followed the directions provided, but my problem Computer Monitor No Signal

Use a shorter cable - A long DVI cable can prevent some video cards from reading the EDID data from the monitor. Pressto select corresponding mode (If this model has a variety of input ports) -> Select the correct input port NOTE: If this model doesn't have the button, please press "MENU"  to enter Helpful +30 Report Niranjan Jun 25, 2010 at 12:03 AM Step 1 : Just replace ur power supply inside ur cpu with other one! http://windowsrefund.org/turns-on/computer-not-projecting-anything-on-monitor.php didn't quite understood what you said Related Resources Monitor not working after installing a new graphics card!

Like I said, you can tell the desktop is being extended, and the device manager shows two monitors connected. Pc Turns On But No Display Or Beeps You should have already checked the RAM using the article I mentioned above, but you should also make sure the fan on the video card is running. If Windows is visible then it's probably not a hardware problem because the old, slow VGA mode puts way less strain on the DVI transmitter, cable, and receiver than any mode

Some monitors seem to be inconsistent when making that choice.

Then I removed my dvd rom and suddenly whole system back into life..after formatting my pc is running now like a new one..thanks man. If there is still no image and your monitor has a Source button, press the Source button. There's really no point in not using reduced blanking all the time. Monitor Problems Horizontal Lines The notebook screen remains up for a few seconds and then goes black as the INTEL inspiron switches back over to Monitor as primary display.

This resets the electronics on the display. ok IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product Warranty For flat panel LCD displays, set the display resolution to the display's native display resolution. have a peek at these guys works a treat again.

on my graphics card there's a small 2 pin hole thing which needs to probably connect to the motherboard. If both monitors are plugged in (white and blue ports) only the one with the adapter shows anything. If you do get a picture, follow the directions immediately below to change the refresh rate and resolution. • Changing the Refresh Rate and/or Resolution The optimum refresh rate for Solutions: check your DVI cable type This may sound silly but have you checked your DVI cable to make sure you have the right kind?

Restart the computer. No POST Does the computer beep when it is turned on or does it sound like the computer is working? It's a shame to have cable length limited by something as easy to implement as an I²C bus rather than the difficult to implement TMDS connection. I am having this problem 2.

Increase the display resolution as follows: Changing Display Settings, Background Image, and Screen Saver in Windows 10, 7 Changing Display Settings, Background Image, and Screen Saver in Windows 8 Disable the Go analog - If you're running in digital mode and you've never gotten the monitor to work at all then try analog mode. That's because the digital data only has to be above a certain quality level to be correctly received. Screen remains Blank • Make sure the power cord is connected securely and completely at the monitor and at the electrical outlet. • Some Samsung monitors have another power switchat the

If the monitor is on, but nothing is showing up, try to press the menu button to bring up the built-in monitor controls. Problem with the computer If the computer was working when the screen went blank, the computer might have a problem. Feb 15, 2007 #6 kwabou TS Rookie Topic Starter The menus accessed by pressing the button on the front of the monitor? If the display still shows a black screen, the video hardware might need to be replaced or serviced.

If the video card fails to get the EDID data from the monitor then Windows may (I'm not 100% sure) fall back on the .INF file which is currently selected.

© Copyright 2017 windowsrefund.org. All rights reserved.