Home > Hard Drive > Boot Using A Slave Drive

Boot Using A Slave Drive


The 3rd partition (shared FAT16) could be used, but I don't currently have anything installed to it. Would that be possible without wiping the disk completely? For example Microsoft does not offer booting Windows from USB today. My master drive now has a bad block. http://windowsrefund.org/hard-drive/cannot-master-boot-but-can-see-files-as-slave-drive.php

Last edited by aceplace57; 11-06-2010 at 06:29 PM.. On some models, for example, you may need to select an option such as "First Boot Device" after accessing the hard drive boot menu to change the primary hard drive. In a master/slave setup, a flat, wide parallel cable runs from an interface on the motherboard to the hard drive(s). User Name Remember Me? http://smallbusiness.chron.com/boot-secondary-hard-drive-53295.html

How To Slave A Sata Hard Drive

Although it can be done, getting them to work on the slave may mean you have to reinstall ALL the OSes on the first two disks if you need to reinstall colectcallgrl, Dec 5, 2008 #7 Fred_G Heat packin' geek Does the BIOS detect the drive and say all is well, but XP won't start? Moving several hundred gig of personal files, music, videos etc. then the second drive in sata 1.

Login now. before you try this SAFE method.good luck. It's wise to check your motherboard manual and connect a new drive to a matching SATA port (one running at the same speed as your drive). How To Install A Second Sata Hard Drive If this still does not work, you may have to clear and reset the Boot Priority.

Although the new WD SATA HDD may have a set of pins and a jumper, you should NOT change the jumper. How To Boot From A Second Hard Drive I spent over 5 hours solid trying every possible solution under the sun to fix my problem. problem: i recently encountered this problem as i was trying to boot up my new SSD (solid state drive).i have installed a windows 7 copy on it and wen i disconnected References (2) GIGABYTE: GA-MA770T-UD3P: User's ManualTechRadar: BIOS Tips and Tweaks for Speed and Extra Functionality | News About the Author Ruri Ranbe has been working as a writer since 2008.

If that turns out to be your situation, you should be able to use only the Secondary IDE port.2. How To Boot From Second Hard Drive Windows 7 Thanks for the tips. colectcallgrl Private E-2 I have 2 hard drives. The parallel cable itself might also be labeled as to specific master/slave ports.

How To Boot From A Second Hard Drive

Remove any reference to those devices. internet It should say No OS found. How To Slave A Sata Hard Drive So if it does not work, could be the port is dead. How To Slave A Hard Drive I spend 2 days trying to fix boot manager after mistakenly formatting my c: (windows on d:) and able to boot.

With SATA, all you need is a free SATA port on the motherboard, a spare bay in which to mount your second hard drive, and a SATA cable to connect the check my blog The PATA HDD is set to Master with the jumper. Your computer will automatically reboot. Touch the metal portion of the chassis and then loosen the screws securing the secondary drive to its bay. Master Slave Hard Drive Setup

SUBSCRIBEAs low as $1.00/week Home Local In Local Neighborhoods Houston & Texas Traffic Weather Education Politics & Policy Election 2013 Chronicle Investigates Obituaries Staff Blogs Reader Blogs Columnists Opinions & Editorials The master/slave relationship is part of a transmission protocol that bridges communication between a hard disk and the motherboard it’s attached to. is a lot of work. this content So if you did actually change the jumper on the new SATA HDD, restore it to its original position.2.

More resources See also My computer won't boot. How To Install A Second Hard Drive Windows 10 Is this because the port is bad or because the cables are not interchangable? Flag Permalink This was helpful (1) Collapse - thank you sooo much for the post by buju357 / April 26, 2011 11:10 AM PDT In reply to: You saved my life

to a point that i had to pres the F8 key in order to boot the old hard drive witch was competing on the boot up with the new failed boot

Need more storage space? Then maybe test that caddy unit. So their desgination is now dictated by the ATA ribbon cable connection. How To Boot From Second Hard Drive Windows 10 If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post).

I'm using a boot loader called XOSL (google that and it's page comes out near or at the top). Select "Boot" or "Advanced BIOS Features" using the arrow keys. Use the arrow keys on the first boot device. have a peek at these guys Reading this over, it seems that I have, in fact, gotten every OS I use on this machine to boot from a slave, at one time or another.

When I open up the case to install, I notice that the old HD is configured as a master on the primary controller. Now it doesn't power up at all. Switching the IDE cable to the Primary channel connector should work if that IDE channel is working. Check the documentation included with the drive, or check the drive for an instructional sticker, for further assistance.

No problem: just buy and install another hard drive. If you are thinking of trying this, be aware that Winblows (any version) is especially hard to fool into doing what you want, because of Microshit's arrogance. Delete that to kill Vista. Linux and a few other OSes do offer such a feature.

bye bye windows. SUCCESSES!!---------if you follow this steps there is a very high chance you ill get the same results.-----in sort the steps : 1 power off your pc and UNPLUG from wall power Preview post Submit post Cancel post You are reporting the following post: How to make a hard drive bootable? Fully sanctioned and supported.Bob Flag Permalink This was helpful (0) Collapse - Check out by jamhelmcor / April 14, 2011 4:40 AM PDT In reply to: Then get it on USB

These would be the first things I'd try if they don't work hold on someone else will correct me and post another suggestion.

© Copyright 2017 windowsrefund.org. All rights reserved.