Home > Hard Drive > Anything Special Need To Be Done For SATA Drive?

Anything Special Need To Be Done For SATA Drive?

Contents

If you are adding a blank hard drive, continue with the next step. I a senior citizen with only a little computer knowledge. and ur write he DIDNT start off with TAKE drive out of box… jeeees…. If you are adding storage to your existing configuration, you should leave the original hard drive installed where it is and skip down to Step 5. navigate here

If you are installing a hard drive that is 2 TB or greater, HP recommends formatting the drive using GPT partitions. I don't see an option for autodetecting hardware in my BIOS, by MSI. I've saved this to my useful websites list for easy reference! Right click the new drive and then click Format.

How To Connect Sata Hard Drive To Motherboard

Figure : Finding the version for BIOS version 7 or greater If your computer has BIOS version 7 or greater, go to Configuring the hard drive in BIOS version 7 or System runs windows xp.If I look at the drives in computer management, both drives show up as healthy, but one is labeled "system" and the other is labeled "page files" There thanks Reply Jenna says: March 20, 2009 at 1:22 pm Okay… here is my issue and I am at whits end. Before you begin working on the interior of your computer, make sure you discharge any electrostatic charge you may have.

Keep the drive in the protective anti-static container until you are ready to install it to minimize handling damage.Drive electronics are extremely sensitive to static electricity. I really appeciate it 😀 Reply malcolm says: November 9, 2007 at 6:08 am Hi I've got a system with a 40gig drive which i want to ghost to a 250gig Here's how to install a new internal drive as extra storage or as a new boot drive. Sata Power Connector You may need to remove stickers to access all of the screws. 4 Remove the old hard drive.

Please help. How To Connect Hard Drive To Motherboard Contributing Editor Lincoln Spector writes about technology and cinema. If using a SATA to IDE adapter, follow the instructions for the adapter. click for more info But in Windows one of the two drives doesn't appear.

Please advise me physical installation, formatting and set partitions to the drive. Sata Power Cable Since the operating system does not require a fresh installation, preparing your drive for use is easier. It may have its own BIOS to check. The document also provides instructions for replacing an IDE drive with a Serial ATA (SATA) drive.

How To Connect Hard Drive To Motherboard

Ground yourself, either by wearing an antistatic wrist strap, or by touching grounded metal. 3 Access the old hard drive. https://www.pcmech.com/article/installing-a-hard-drive-step-by-step/ If your case permits, try to maintain some space between the new drive and any existing drives to help promote airflow and cooling. How To Connect Sata Hard Drive To Motherboard Hard disks have passed through a long evolution of connectivity and data transfer standards. Sata Hard Drive Power Cable My SATA cable is now connected to both my internal HD and the new HD I have just put in, and it then goes to the motherboard.

Is there anyway to solve this problem? check over here I tried to re-set boot priority and drive priority, but I get the same thing. It's not that hard. Be sure that the metal side faces up and the black, plastic side faces down. Sata Interface Cable

jQuery © 2008 John Resig Reproduction of OSNews stories is permitted only with explicit authorization from OSNews. Reply Kallon says: July 13, 2014 at 5:28 pm I know this is a while from original comment but couldnt you just remove the other hard drives and make the one Then check whether a CD comes with the drive, providing drive-specific information and general upgrade assistance. his comment is here If your old hard drive is IDE, look for the SATA connector on your motherboard.

If you are installing a Serial ATA drive as a replacement for an IDE drive, check the motherboard for an open SATA slot. Hard Drive Connector Types Most IDE disk drives use an IDE data ribbon connector and a white power plug, while most SATA drives use the SATA data cable connector and a black power plug. The safest way to work inside of a computer is to wear an antistatic wrist strap while working on the computer. 3 Find the hard drive bay.

Your website got me passed this and told me how to do it without that.

What about if you have a IDE hard drive and you upgraded it with a SATA adapter? If you are upgrading or replacing a hard drive, you should see one already installed. 4 Disconnect the old hard drive (if replacing). I had no idea that "disk management" section existed 😀 Once i found it i initialized the HD and am currently formatting it. Sata Data Cable But then it just freezes up.

In the article, it mentioned that the PC should not be plugged into the internet until XP SP3 is installed; they then provided the link to d/l the SP3 patch. Save changes and exit the utility. See if an unused SATA port lies nearby on the motherboard or an interface card. http://windowsrefund.org/hard-drive/cant-format-my-sata-drive-help.php The PC will determine master/slave status according to the drives' placement on the cable ("master" at the end, "slave" in the middle).

http://forum.pcmech.com/forumdisplay.php?f=40 Reply Big Ste says: September 26, 2007 at 4:43 pm Very helpful, thanks. The following YouTube video demonstrates the installation procedure.

For more practical installation tips, check out the following articles: How To Install A Second IDE Hard Drive On An Older PC ESD occurs as a result of static electricity built up in the body and can cause serious damage to electronic components. This is an easy way to add an IDE drive to a motherboard with a single IDE motherboard socket.

The worst part about installing hard drives is setting the jumpers on the drive so that it works correctly with your current hardware. Your new drive should appear, with a black bar indicating it isn't partitioned. If your computer is still plugged into the wall (with the switch off), you can touch any of the exposed metal of the case to discharge. Click Next yet again (to the Format Partition screen), and ensure that "Format this partition with the following settings" is selected and that the "File system" drop-down reads "NTFS." Click Next

If so, screw a set onto the new drive (look inside the case for spares), then slide the drive into its bay. Motherboard card slot. Tech Reviews Tech News Tech How To Best Tech Reviews Tech Buying Advice Laptop Reviews PC Reviews Printer Reviews Smartphone Reviews Tablet Reviews Wearables Reviews Storage Reviews Antivirus Reviews Latest Deals Also verify that the two SATA connection ports in back of the drive are accessible. 7 Secure the drive.

How do I get my computer to recognize it. Not one problem with your directions!!! How would they know whether they have an IDE or SATA hard drive if they have never even heard of those abbreviations before? But there are exceptions.

If you are using an IDE hard drive, you want to optimally connect the drive on a different IDE channel than your DVD/CD drives. You have to click the Action button. Flash memory packaged in an HDD-like form factor, to be used in place of a hard drive. Thanks for the help.

Partition: A section of a hard drive (or SSD) that appears to the operating system as a separate, independent drive. Then i remembered that one is set to slave the other to master what do i set the third one to i tried slave but still screeched at me!

© Copyright 2017 windowsrefund.org. All rights reserved.