Home > Hard Drive > Adding A SATA Hard Drive To A PC With Two Existing IDE Drives?

Adding A SATA Hard Drive To A PC With Two Existing IDE Drives?

Contents

I owe you one. Jumpers are small black plastic sleeves that slide over the top of metal pins. Yes No Not Helpful 6 Helpful 7 How can I install an operating system on the extra hard drive? However, there is often a diagram on the top of the drive telling you how to set the jumpers, and if not there will certainly be instructions in your hard drive's http://windowsrefund.org/hard-drive/adding-ide-hard-drive-to-a-sata-setup.php

Reply Www.diolt.com February 28, 2011 at 10:27 am Hello thanks for the nice information you shared Reply FreeReferrals February 27, 2011 at 9:40 pm Thanks this was very helpful and I So you could take an old 386 drive from 1988 and plop it into your Pentium 4 from 2005, and it would work! Each setting changes how your computer operates and you can inadvertently make your computer inoperable. i want to format it… thanx Reply Tim says: January 1, 2009 at 2:16 pm All the Bickering that I read in the begging of this is absolutly POINTLESS!!!!

How To Connect Ide Hard Drive To Sata Motherboard

Reply Douglas says: September 26, 2009 at 3:28 pm Oh My God! The master device is connected in the middle of the cable, and the slave at the end of the cable. Reply Adam August 24, 2016 at 3:49 pm @MikeTek the middle connector is the master, the end is the slave. All Rights Reserved.

Most do not, but you never know. They will be labeled on each connector). How about installing a new and different hard drive in a laptop? How To Install Ide Hard Drive There are no jumpers to worry about on SATA drives.

The drive can be a SATA or PATA hard disk drive (2.5" or 3.5"), or it could be any kind of optical drive, such as a SATA DVD or legacy CD Ide Hard Drive Jumper Settings pinpoint where (in which HDD) you have installed the operating system – so that the BOOTMGR could be loaded to log in to windows as usual; otherwise you’ll have to face How do I get my computer to recognize it. internet There are 3 connectors, notice the difference in distance between the connectors.

You can start saving files on your new drive immediately. How To Connect Ide Hard Drive To Motherboard Win+R (initialize run command) 2. Reply Tyler Thompson says: September 10, 2007 at 2:10 pm David, When you clone a drive, it copies it exactly as it were before. At this point, you may want to make some quick sketches of just how everything is in there: Which direction is everything facing?

Ide Hard Drive Jumper Settings

Thanks, Duane Reply Andypandy says: April 4, 2008 at 6:28 pm Thanks for this great info, it made my job soooo much easier. http://www.easeus.com/resource/install-ide-hard-drive.htm Is there space available to add another hard-disk drive? How To Connect Ide Hard Drive To Sata Motherboard The figure below depicts the jumper settings for the U-Series and Barracuda ATA drive families (most Seagate ATA drives above 20 GBytes). How To Connect Two Hard Disk In One Pc Just use the power plug you have, no worries.

How can I connect this? http://windowsrefund.org/hard-drive/adding-a-2nd-hard-drive.php Yes No Not Helpful 1 Helpful 0 Unanswered Questions How do I add an extra hard drive and keep it as a drive letter? If you are not sure, open the computer case and try to determine the type of the used drives from the view. Reply Germ says: August 16, 2007 at 1:07 pm I inherited my works old server computer and I want to convert it to a stand alone personal PC. How To Connect Two Sata Hard Disk In One Pc

The older tower Gateway pc wont start, I tried placing the hardrive with win8 in the newer Gateway tower, get blue screen that freezes, with this message: Checking file system on Choose the primary drive and simply drag and drop. Flag as... navigate here If i were to plug it in, would it be able to recgonise it?

They're sold everywhere, but you want to avoid the smaller hard disk drives made for laptops. Sata And Ide Hard Drives Together Let’s do this! 1. My hard drive crashed, but I had a back up one.

Cheers Tim Reply Donny says: January 3, 2009 at 4:19 pm Fantastic article!!

malcolm Reply angie says: November 11, 2007 at 3:44 pm hey i have been trying to get this to work ok so this is what i am doing i have a The way to eliminate static electricity is by grounding yourself. the least you could do. ____________________________________________ For folks thinking of buying a new HDD, it is wise to know the supported SATA type (SATA II/SATA III) and SATA PORT SPEED (SATA Seagate Ide Hard Drive Jumper Settings However, as some readers pointed out, the process of adding an IDE drive is significantly more difficult than a SATA drive, so in the interests of completeness and for those of

If you did use a controller card, it will pop up a screen showing the name of the card and any drives it has detected. But then it just freezes up. i dont understand this as my dvd drive is working fine thrue the ide cable and when i unplug my dvd and stick my hard drive nothing ...and i dont have http://windowsrefund.org/hard-drive/adding-an-old-ide-drive-into-a-comp-with-a-new-sata.php wikiHow Contributor You could purchase at a computer or electronics store, or online.

Wanted to install in new box. They all are marked master slave etc. If you need a separate controller card, install it now into any unused motherboard slot. What is this?

Thanks for any advice that you guys give… Reply Greg says: March 26, 2009 at 8:04 pm I just installed a new HD and followed all the steps, but while it The metal the case is built from is thicker than average so the screws I have do not reach to try and install it that way.

© Copyright 2017 windowsrefund.org. All rights reserved.