Home > Hard Drive > 4 Ide Devices On One IDE Channel?

4 Ide Devices On One IDE Channel?

Contents

ATA, ATAPI, IDE, and other computer interfaces help and support. I have Windows 2000 with an AMD 2800 chip and A7V8X mobo. Frequently Asked Questions: Can I connect a older ATA33 drive with my newer ATA66/100/133 drive? A: Solve an audio problem on an HP computer by checking the settings, testing the devices and restoring drivers.

There is a sample about Seagate hard drive jumper setting. also I dont have a cd/dvd rom. When you first start your machine enter into the BIOS and make sure the drive was identified properly. Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account? https://www.reference.com/technology/many-devices-can-linked-single-ide-channel-32b1ae20b69a609

Ide Hard Drive Jumper Settings

Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. Along one side of the cable is a stripe. As long as your motherboard has both SATA and IDE connections available and you set the switches on the drive appropriately, it should work! Write out a quick table to figure out how it is currently set up, like this: CHANNEL 1, MASTER: CHANNEL 1, SLAVE: CHANNEL 2, MASTER: CHANNEL 2, SLAVE: Probably your hard

It should be the Master, and the hard drive (if you have one) Slave. First of all Master, Slave? TechSpot is a registered trademark. How Many Ide Controllers Are Available On Most Motherboards Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended.

Same goes for SATA controllers.I think some SATA drives have legacy IDE plugs on them, but I'd only use the SATA plug with the small serial cable. Several functions may not work. A Cable Select cable can be used with master/slave drive jumpering. http://www.mikeshardware.com/howtos/howto_connect_ide_hd.html Dismiss Notice TechSpot Forums Forums TechSpot Core Build a PC Today's Posts 4 ide devices on one IDEchannel?

Cable Select is defined in the ATA-2 and ATA-3 specifications. What Is The Voltage Of The Red And Yellow Wires On Most Power Supplies? PlayStation Vue: How Do They Compare? Set The Jumpers & Plug In Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector The Primary connection ALWAYS gets the 80-wire cable.

How To Connect Ide Hard Drive To Sata Motherboard

EaseUS Partition Master, comprehensive hard disk partition tool and system optimization software for Windows-based administration, enables you to easily partition the hard disk or change/extend partition without data loss under Windows. Oh yeah, keep hard drives together too, on the motherboard connector labeled 0. Ide Hard Drive Jumper Settings Make sure that both IDE channels are enabled. How Many Hard Drives Can Be Connected To A Single Ide Cable do you think that would work?thanks for any help,iak. - iak.http://www.iakstudios.com 7 answers Last reply Mar 31, 2003 More about devices cable SpateMar 30, 2003, 8:40 PM I thing IDE cables

PEOPLE SEARCH FOR Soft32 Softpedia Explore Q: What is an example of a hybrid computer? The IDE HD had to be on the secondary IDE cable in order for it to be recognized by the sata drive. About CNET Privacy Policy Ad Choice Terms of Use Mobile User Agreement Help Center If this is a secondary drive then you're obviously after pure storage space so just make it a primary partition and allocate 100% of your space to it. Ide Cable Select

Select New Partition. Format the drive. by Mad53704 / December 4, 2006 12:48 PM PST In reply to: New SATA HD booting mantining old IDE HDs. First of all look go back to the front page in your BIOS and select integrated peripherals.

Aug 24, 2006 #4 (You must log in or sign up to reply here.) Show Ignored Content Topic Status: Not open for further replies. Ide Cable Definition Perhaps a solution is around the corner as there is a draft for a FireWire ATA interface. My 40 GB hard drive only show up as 38.2 GB: The formatted space will always be a bit less than the advertised storage capacity.

After all, you need one connector for the motherboard, one for the master and one for the slave IDE device.

Save and exit the system setup program. Discussion topics include SSD, SATA drives, USB drives, external hard drives, RAID arrays, backup, IDE drives, network attached storage (NAS), thumbdrives, Western Digital, Kingston, LaCie, and SanDisk.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General Protect the drive from static discharge by wearing a grounded wrist strap. Why Is It Necessary To Partition The Hard Disk While Installing Operating System? The black connector attaches to the primary, or master, drive.

Note: You wouldn’t normally run devices outside of the case like this, but for the purposes of checking if they work, it’s a lot easier than unscrewing them and poking around A: Quick Answer Two devices can be linked to a single IDE channel, although most computer motherboards have two separate IDE channels and are therefore capable of supporting a maximum of The Master drive goes on the black connector at the end of the cable, the slave drive connects to the gray connector in the middle and the host adapter connects to One thing to always remember...you can retain use of your PATA/IDE devices very easily, no matter what the motherboard specs are...by just using a PATA/IDE controller card in one of your

solved i need to hook up a old surround sound using video 2 and video 3 to 2 cable boxes.

© Copyright 2017 windowsrefund.org. All rights reserved.