Home > Dvd Drive > BIOS Not Detecting Internal SATA DVD/CD Optical Drive

BIOS Not Detecting Internal SATA DVD/CD Optical Drive

Contents

I hope I can restore it to its previous state and retrive some data back too. Thank you for your help. See if you can find a way to reset eveything... Please help me if you can. weblink

I'm having some seriously annoying problems with my pc. In Standard IDE mode, you can connect Serial ATA boot/data hard disk drives to these connectors. If you DO want to set up a RAID array, - you must set it up BEFORE you install an operating system. - you must install drivers - if you are Is any drive recognized there?If not, go to Integrated Peripherals and make sure that SATA and IDE controllers are enabled.Just to make sure - power cables are connected to HDD and

Dvd Drive Not Detected In Bios Laptop

it really worked, now i get my dvd drive Edited by harsh giri Monday, June 04, 2012 8:43 AM Monday, June 04, 2012 8:38 AM 0 Sign in to vote worked note I had Windows XP installed on my HDD through my earlier PC & was running Intel Dual core processor with gigabyte Mobo.Can anyone advise what I can do in BIOS I tried changing the DVD-RW's SATA cable to a new one, tried connecting the DVD-RW in other SATA2 port but still same. If this is the first time you've seen this Stop error screen, restart your computer.

Any ideas? They won't open and not powered perhaps.I can't hear any obvious noise from them. So up the proverbial creek on that one.I can't instal Windows without the SATA optical drives working - not detected. How To Check Dvd Drive In Bios The drive itself isn't defective.

But it appears to me that the system is capable of being re-set so that it can then be reconfigured. Some motherboard manufactures disable unused ports in the BIOS by default. It worked ! http://www.tomshardware.com/answers/id-2073017/dvd-rom-recognized-adding-hard-drive.html In "Integrated Peripherals": - PCH SATA control mode is always been [AHCI] - SATA Port0-3 Native Mode is always been [Enabled] Please help me to solve this problem.

SATA II drives - max burst data transfer speed 3.0 gbits/sec, = 300 mbytes/sec(SATA drives use 10 bits per byte when moving data, not 8 bits per byte)SATA 3 a.k.a. Sata Hard Drive Not Detected Tuesday, February 19, 2013 7:21 AM 0 Sign in to vote Type cmd in Windows 8 Metro UI and press cltr+shift+enter. This will stop any power saving commands from being sent.Turn on the system. You may also want to open Device Manager and verify that the yellow exclamation and error code on the CD or DVD drive is gone share|improve this answer answered Sep 12

Cd Dvd Rom Not Detected In Bios

However, with one of them, for whatever reason, when I first installed it, there was something a little iffy about the main connector - I found that if I positioned the http://www.tomshardware.com/forum/357221-31-motherboard-recognizing-drive If you used power cable adapters that are not on the power supplies wiring are you sure they work ? Dvd Drive Not Detected In Bios Laptop Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? Dvd Drive Not Showing In Bios Thanks slance310 ....

Please tell me how to go about it Ask a new question Read More SATA Storage Related Resources New SATA DVD Drive has no power and not detected in the BIOS have a peek at these guys Change Step 1 in the above Post to: Select Search from the Charms Bar, and search for cmd.exe. Operating Systems ▼ Windows 10 Windows 8 Windows 7 Windows XP See More... All going well. Bios Doesn T Recognize Dvd Drive

They were SATA 3 GB/s ports, though, and the one I had that came with the motherboard was connected to a 6 GB/s port. I went ahead and retyped out the command line but I didn't change any spaces from before and it accepted the process. Would that make a difference? check over here The easiest way to get around that is....

Report • Start a discussion Ask Your QuestionEnter more details...Thousands of users waiting to help!Ask now Weekly Poll Do you think Google should sell budget phones in the US? Related Resources Bios no longer detects my sata hdd or dvd drive HDD/SSD/Optical Drive not detected through SATA ports, 2nd motherboard in a row to have this problem. What do I do about this?

Can't find your answer ?

SATA ports should be backwards compatible, so if you had the same problem on 3 different ports using the same cable, then I would suspect that cable is bad. Tuesday, December 18, 2012 12:04 AM 0 Sign in to vote This works one hundred percent. Nothing worked. Can't find your answer ?

Didn't realise the damage you could do otherwise. Type following and say enter reg.exe add "HKLM\System\CurrentControlSet\Services\atapi\Controller0" /f /v EnumDevice1 /t REG_DWORD /d 0x00000001 3. It is a ASUS motherboard, M3N78-EM, AMD2+, NVIDIA chip set 8300. this content thanks for your help, it is much appreciated.

I don't have the resources to test the DVD drive in another PC now so I reconfigured the SATA cable connection to original and removed my new HDD (WD 2T): SATA3_0 The ODD works with the cable I received with the motherboard.Welp, my brain is breaking... I have a decision to make. Tried the SATA cable I bought: Same problem, tried on two different ports.

THANK YOU, THANK YOU, THANK YOU!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Please help me out. Startup Repair > Diagnosis and repair details: > Startup Repair diagnosis and repair log --------------------- last succesful boot time: 1/15/2010 number of repair attempts: 12 Session details --------------------- System Disk = And the fact that it won't eject tends to say to me it's defective, because that should work regardless, but since it's quick and easy to do the above mentioned tests,

somehow it doesnt have the slikness of vista.. If this doesn't work, post back with more details. PS I swapped connections from bottom to top and the DVD now works. No, create an account now.

It started about two weeks ago when I opened a file from the internet and the whole thing came crashing down. I think IDE/Legacy is disabled or not set as active. This Enermax model must have those coming from at least two different places for at least one of the voltages, probably the 12v (internal desktop hard drives and optical drives require Ask a new question Read More New Build Cable Motherboards Systems Related Resources solved DVD drive not recognizing os disc?

Reply Leave a comment Helpful +2 Report vaiouser Jan 27, 2010 12:23PM I have installed it. Marked as answer by Arthur XieMicrosoft contingent staff, Moderator Friday, March 16, 2012 8:00 AM Sunday, March 04, 2012 11:56 PM 0 Sign in to vote Bob, do you still use If you can boot the Windows installer from a disc with the known good cable from one of the HDDs, then it would be a bad cable. I've never had any problems with any of them that I've bought for my computers or for other people's computers - the oldest one is about 9 years old.

Computing.Net cannot verify the validity of the statements made on this site. If I buy a foreclosure at courthouse auction, am I in any way responsible for debt on the property?

© Copyright 2017 windowsrefund.org. All rights reserved.